ACOM A1200S

ACOM A1200S fra oss igjen til den beste pris. Fri frakt. OBS. Bestillingsvare.  Leveringstiden er 8 dager fra bestilling

Mere info:

ACOM 1000 160-6m amplifier

The ACOM 1000 HF Linear Amplifier is the world's best value in an amateur HF amplifier.

The ACOM 1000 gives you a comfortable 1000 watts output on all amateur bands from 160 through 6 meters.

• Frequency Coverage: All amateur bands 1.8-54MHz; extensions and/or changes on request. 
• Power Output: 1000W PEP or continuous carrier, no mode limit. 
• Intermodulation Distortion: Better than 35dB below rated output. 
• Hum and noise: Better than 40dB below rated output. 
• Harmonic Output Suppression: 

        -1.8-29.7MHz - better than 50dB below rated output; 
        -50-54MHz - better than 66dB below rated output. 

• Input and Output Impedances: 

         - nominal value: 50 Ohm unbalanced, UHF (SO239) 
           type connectors; 
        - input circuit: broadband, VSWR less than 1.3:1,
          1.8-54MHz continuously (no tunings, no switching); 
        - bypass path VSWR less than 1.1:1, 1.8-54MHz 
           continuously; 
        - output matching capability: better than VSWR 3:1 or 
           greater at reduced output levels.

• RF Gain: 12.5dB typically, frequency response less than 1dB (50 to 60W drive power for rated output).
• Primary Power: 170-264V (200, 210, 220, 230 & 240 nominal taps, 100, 110 & 120V taps on request,  +10%-15%tol.), 50-60Hz, single phase, 2000VA consumption at rated output. 
• Complies with CE safety and EMC requirements, as well as FCC-regulations (6,10 & 12m bands lock provided). 
• Size & Weight (operating): 

        - WxDxH: 422x355x182mm, 22kg. 
        - (16.6x14x7.2 inches, 48.5lbs) 

• Operating environments: 

        - temperature range: 0...+50 degs.Celsius; 
        - humidity: up to 75% @ +35 degs.Celsius. 
        - height: up to 3000m above sea level without output deterioration

Gratis frakt, pr nå er leveringstiden ca 10 dager.

Mere info:

• Five inch (5”) (108x65mm) high resolution color display, 800x480 pixels and 24-bits colors.
• The final stage uses field effect (MOSFET) transistors type BLF188 from NXP, designed to withstand high mismatch (SWR) at the output and intended for operation in aerospace, industrial, mobile, and radio broadcast applications.
• Compatible with all transceiver models available on the market - does not need any special signals: “ground on transmit” (PTT) and 50W of RF drive power is sufficient.
• Broadband input circuit providing a perfect transceiver load with SWR below 1.2:1 (typically 1.1:1), without retuning throughout the whole frequency range from 1.8 to 54MHz
• The overall operation of ACOM 1200S is extremely simplified: the screen menus are intuitive and easy to follow and no special skill is required from the operator when changing frequency bands
• Possibility of automatic control – when connected to a transceiver with a CAT interface, the amplifier monitors constantly, duly follows the operating frequency, and changes the bands accordingly.
• Even if not connected with CAT interface, the amplifier monitors the frequency of the input signal through the built-in frequency counter and automatically switches over the bands.
• Remotely controlled by RS232 interface.
• Takes care of itself during operation due to the continuously working protection circuits in all modes.
• The operator can monitor digitally more than 10 parameters concerning the working regime of the amplifier.
• Easy maintenance – detailed data (55 parameters) about each of the last 28 hard-fault protection trips is stored in the amplifier’s nonvolatile memory.
• Convenient for expeditions and field operation: extremely compact and light construction, extended mains voltage range (93V÷265V), limited inrush current and purely sinusoidal consumed mains current, automatic Power Factor Correction (PFC) – all significant parameters in operation from unstable mains, generators etc. features achieved thanks to the built-in switching mode power supply (SMPS).
• Perfect electromagnetic compatibility (EMC) both with the highly sensitive as well as with the powerful appliances in the radio station (receivers, computers, more amplifiers) exceeding the standard EMC requirements due to the use of PFC and the built-in additional radio-frequency filters.